High Quality Laboratory Electronic Workbench - BR1275

Frame Material of Workbench

Common material is cold rolling steel sheet, besides there are aluminum extrusions and winding bar

Table top Material of Workbench

1.Polymer table top: the surface of density board is sticked with 2mm polymer skin .The thickness includes18/25/30/50mm .The bordure includes right angle and rounded corner

2. Antistatic table top:the surface of density board is sticked with 2mm antistatic skin.The thickness includes 18/25/30/50mm.The bordure includes right angle and rounede corner

3.Sheet iron\stainless steel table top:the base board is density board and its each side is wrapped up with 0.8mm sheet iron as well as 1.0mm stainless steel. Oil proof , easy to clean. the thickness includes 20/25/30/50mm

4.Fire proof plate table top: also named density board table top, both sides are painted with fire retarding coating, the thickness includes 18/25/30/50mm

5.Multi-layer plate table top: pressed with multi-layer thin board ,high water-proof perfermance. The thickness is 30/50mm

6.Wood table top:Good appearance, the most expensive. the thickness is 25/50 mm

7,Synthetic iron table top: the surface of base board (fire proof) is covered with a certain height (5/6/8/10mm) sheet iron. Or there is only a certain height sheet iron as long as it can meet the load requirements . Good impact resistance.Applicable to the bench and the maintenance station etc.The thickness equals to the thickness of base board + the thickness of sheet iron

Dimensions of Workbench

The standard dimensions are 1500x750x800, the height of lamp bracket is 1000mm

The length shall not exceed 2400mm, the width shall not exceed 1200mm ,because the widest width of polymer skin or antistatic skin is 1200mm.If the width exceeds 1200mm, two table tops should be pieced together

Detailed dimensions

Heavy duty workbench: the leg section size:100x50mm crossbeam:90x50mm

Medium duty workbench: the leg section size:70x40mm crossbeam:70x40mm

Configuration of Workbench

(1) Drawer cabinet

Drawer tool cabinet can be hung below the table top or used as the leg to brace the table top. The minimum height of drawer is 75mm and must be the multiple of 25. Otherwise it's nonstandard drawer and the cost will be increased.

Dividers can be configured in the drawers.The standard dividers are 3x3 and customer requirements are available.

The standard dimensions of drawer tool cabinet are 410x570mm and 560x570mm. The height of drawer tool cabinet depends on the amount of drawers.

The drawer guide rail includes single rail and double rail. The load of single rail is 80kg and can be pulled out 80%. The load of double rail is 150kg and can be pulled out 100%

Wide aluminum alloy handle with PVC card ,.Safety baffle design to ensure the drawer will not fall when fully open.One key to lock all drawers.

(2)Small storage cabinet

Storage cabinet can be hung below the table top or used as legs to brace the table top. Additionally, drawer cabinet and the storage cabinet can be used in combination.

The size of storage cabinet is the same as drawer cabinet ,410x570/560x570mm. Non standard customization.

The cabinet can be equipped with a partition board.

(3)Adjusting foundation

Adjusting foundation includes M8,M10,M12,M16. Medium duty workbench uses M8,M10,M12. Heavy duty workbench uses M16. Adjustable height is 50mm

Material includes pure iron and plastic pad. The plastic pad is for preventing crushing and shock absorption.

(4)Castors

Material: polyurethane caster.

Size:

3 inch (bearing 200kg) , applicable to light duty product

4inch(bearing 400kg) , applicable to tool carts and light duty workbench

5 inch(bearing 600kg) , applicable to heavy duty workbench

6inch(bearing 1200kg). applicable to heavy duty non-standard product

Application

esd workbench|multifunctional workbench|heavy duty workbench|movable workbench|steel workbench